Frequency Range: 4950–5850 MHz (900 MHz bandwidth)
Gain: 2×16 dBi (two ports)
V.S.W.R: ≤1.5 typical, 2.0 max
Nominal Impedance: 50 Ohm
Polarization: Vertical and Horizontal (dual polarization)
Maximum Power: 100 W
KS-D4958V16X2-120
KEESUN
KS-D4958V16X2-120
| Availability: | |
|---|---|
| Quantity: | |
A 5.8 GHz WLAN sector has to serve many clients at once, and a single-polarization panel cannot feed a MIMO radio properly. Two streams need two branches with the same band, the same pattern and a right angle between them, and a linear panel leaves half the radio idle. The demand for a dual-polarized sector panel with real gain has never been higher. The solution lies in one 120° panel that carries both polarizations at 16 dBi. We are proud to introduce the 4.9–5.85 GHz 2×16 dBi Dual-Polarized MIMO Panel Antenna, model KS-D4958V16X2-120, a 430×138×45 mm white ABS panel with two RP-SMA male connectors.
This part answers a 5.8 GHz MIMO sector requirement. The band runs 4950–5850 MHz, which is 900 MHz wide and covers the 5.8 GHz WLAN channels plus the 4.9 GHz range. Gain is 2×16 dBi, so each port carries 16 dBi of its own. Polarization is vertical and horizontal, one port each, which is exactly what a 2×2 MIMO radio needs. The horizontal beamwidth is 120° and the vertical is 7°, so one panel covers a wide sector with a narrow elevation beam. Front-to-back ratio is ≥25 dB, VSWR is ≤1.5 typical with 2.0 max, impedance is 50 Ohm, and maximum power is 100 W. The two connectors sit at the bottom of the back plate on 18 cm RG316 pigtails. The body is white ABS, the panel weighs 1.2 kg, the pole mount takes Ø30–50 mm, and an adjustable clamp is included.
The panel works on three points: two 16 dBi ports on one 120° body, a 7° vertical beam for reach, and a compact ABS panel with an adjustable clamp.
Gain is 2×16 dBi, which means two ports of 16 dBi each, not one port with 16 dBi and a second that is weaker. The two ports sit on the same 4950–5850 MHz band with vertical and horizontal polarization. That is the pair a 2×2 MIMO radio needs: same band, same pattern, 90° apart. The panel is built for IEEE 802.11n MIMO systems, where two streams raise throughput on a multipath channel. A single-polarization panel would leave one radio chain idle, so the second 16 dBi port is the whole point of this part.
The horizontal beamwidth is 120°, which covers a third of the horizon from one panel, and the vertical beamwidth is 7°, which is narrow enough to keep the energy on the ground and off the sky. A 120° sector plus a 7° elevation is the classic shape for a wide sector that still reaches far: three or four panels can wrap a rooftop, and each one pushes its power to the clients in front of it. The front-to-back ratio is ≥25 dB, so a panel does not spill into the sector beside it.
The panel is 430×138×45 mm and weighs 1.2 kg, so one person can mount it on a pole of Ø30–50 mm with the adjustable clamp that ships in the box. The two connectors are RP-SMA male, placed at the bottom of the back plate on 18 cm RG316 pigtails. The RP-SMA interface is the one most 5.8 GHz WLAN radios use, and the bottom placement keeps the cables out of the weather and out of the mounting bracket. The radome is white ABS, VSWR is ≤1.5 typical with 2.0 max, maximum power is 100 W, and the element is DC grounded. The operating range is −40 °C to +80 °C, and the wind rating is 60 m/s.
Two 16 dBi ports, a 120° sector and a 7° elevation beam make this panel useful wherever a 5.8 GHz MIMO radio has to cover a wide area.
Outdoor WLAN sectors: one panel covers 120° at 16 dBi on both polarizations, which is what a 2×2 MIMO access point needs.
WISP hub sectors: three panels wrap a rooftop into a full circle, and the 7° elevation beam keeps the energy on the subscribers.
Point-to-multipoint links: the 120° beam serves many subscribers from one panel, and 100 W leaves room for multi-carrier radios.
Short 5.8 GHz backhaul: 16 dBi and a 7° vertical beam give a usable link across a campus or between two buildings.
Campus and venue coverage: one panel per sector covers a yard, a car park or a concourse without a mast full of small antennas.
Industrial and port sites: the ABS radome and 60 m/s wind rating suit outdoor roofs that see no maintenance.
The 4.9–5.85 GHz 2×16 dBi Dual-Polarized MIMO Panel Antenna, KS-D4958V16X2-120, does one job: it feeds a 2×2 MIMO radio on a 5.8 GHz sector. The 430×138×45 mm white ABS panel covers 4950–5850 MHz with 2×16 dBi, vertical and horizontal polarization, a 120° horizontal and 7° vertical beam, and ≥25 dB front-to-back ratio. VSWR is ≤1.5 typical with 2.0 max at 50 Ohm and 100 W, the two RP-SMA male connectors sit at the bottom of the back plate on 18 cm RG316 pigtails, the panel weighs 1.2 kg, and the wind rating is 60 m/s. For a wide 5.8 GHz sector that needs two streams, this panel is the part that covers it.