Frequency Range: 4900–6000 MHz
Gain: 1.8–4 dBi
V.S.W.R: <3.0
Nominal Impedance: 50 Ohm
Polarization: RHCP (right-hand circular)
Maximum Power: 5 W
KSANT-11982-B
KEESUN
KSANT-11982-B
| Availability: | |
|---|---|
| Quantity: | |
A 5.8 GHz video link flips its polarization every time the aircraft rolls. A linear antenna loses the link at that moment, and the picture drops out on the screen. The demand for a circular polarized antenna that keeps the link through a roll has never been higher. The solution lies in a cloverleaf with four lobes. We are proud to introduce the 4900-6000MHz 4dBi Omni RHCP Cloverleaf FPV UAV Antenna, model KSANT-11982-B, a φ31×78 mm copper antenna with an SMA-J connector.
This part answers a circular polarization requirement. The band is 4900–6000 MHz, which covers the 5.8 GHz video channels and the 5 GHz WiFi range. Gain runs 1.8–4 dBi with a 360° horizontal pattern, so the antenna does not have to be aimed. Polarization is RHCP, right-hand circular, which is the sense most 5.8 GHz video transmitters and receivers use. VSWR is below 3.0, efficiency is about 80%, ovality is ±2, and impedance is 50 Ohm. Maximum power is 5 W, which is the right rating for a video receiver or a small transmitter. The body is φ31×78 mm, the material is copper, the lead is 65 mm of RG141 cable, and the weight is 0.008 kg.
The antenna works on three points: circular polarization through a roll, a round pattern in a small body, and a copper build that weighs 8 grams.
Four lobes form the cloverleaf, and the lobes are fed in phase to make a right-hand circular wave. A circular wave does not care how the aircraft is rolled: the link holds while a linear antenna would fade. That is why a cloverleaf is the standard choice on a 5.8 GHz video link, and why the pattern stays usable when the drone banks hard.
The horizontal pattern is 360°, so the antenna works as an omni and the pilot does not have to point it at the aircraft. The vertical beam is 8–73°, which is narrow at the top of the band and wide at the bottom, and that is what a four lobe element does. Out-of-roundness is ±2, so the pattern stays even as the antenna turns. Efficiency is about 80%, which is good for a part this small.
The body is φ31×78 mm and made of copper, so the lobes hold their shape and the part weighs 0.008 kg. The lead is 65 mm of RG141 cable with an SMA-J connector, which is short enough to mount straight on a video receiver or a transmitter module. The range is −45 °C to +85 °C, humidity is under 95%, the rated wind speed is 36.9 m/s, and the element is DC grounded. Maximum power is 5 W.
Circular polarization, a 360° pattern and an 8 g body make this cloverleaf useful wherever a 5.8 GHz video link has to hold through a roll.
FPV quads and wings: the RHCP pattern keeps the picture when the aircraft rolls, and the 8 g weight does not load a small frame.
Video receivers and ground stations: an SMA-J connector mounts straight on the receiver, and the 360° pattern means the pilot does not have to aim.
Inspection drones: the 4.9–6 GHz band covers the video channel and the 5 GHz WiFi range, so one antenna serves both.
Camera and gimbal units: the small copper body fits a gimbal mount without blocking the lens.
Bench tests: a known RHCP reference antenna is what a 5.8 GHz link test needs.
Short range links: the 5 W rating suits a receiver or a low power transmitter, and the round pattern covers a room or a yard.
The 4900-6000MHz 4dBi Omni RHCP Cloverleaf FPV UAV Antenna, KSANT-11982-B, does one job: it holds a 5.8 GHz video link through a roll. The φ31×78 mm copper body carries four lobes in right-hand circular polarization, with 1.8–4 dBi gain, a 360° pattern, an 8–73° vertical beam and ±2 ovality, at VSWR <3.0, 50 Ohm and 5 W. Efficiency is about 80%, the lead is 65 mm of RG141 cable with an SMA-J connector, and the weight is 0.008 kg. For an FPV link that has to survive a roll, this cloverleaf is the practical choice.